PLUMBING BASICS: A PREREQUISITE FOR INSTALLING A BATHTUB

Plumbing Basics: A Prerequisite for Installing a Bathtub

Plumbing Basics: A Prerequisite for Installing a Bathtub

Blog Article

Rates

We have come across this article relating to How to Install a Bathtub below on the internet and think it made sense to write about it with you here.


Installing A Bathtub
Setting up a tub isn't precisely rocket science, but it does require strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old bathtub with a brand-new one is additionally a reasonably challenging task. If the old bathtub is readily accessible, the task can move quickly; if you need to open a wall to remove the old bathtub and also position the brand-new bath tub, the task is much harder. In either instance, the project is within a home handyman's skills, although you will certainly need a helper to move out the old bathtub and set in the brand-new one. Make certain you have qualified yourself for the task and also fit trying it. As opposed to employing a contractor to take control of a halfway-completed project, it is far better to take into consideration employing one before you begin. Opportunities are you may require a specialist plumber to make tube connections.
This short article will certainly assist you set up a brand-new bathtub in your bathroom if you have already gotten a new bathtub as well as don't need to change the setup of your previous supply of water pipelines.
Your devices and product checklist should comprise the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipe Caps


  • Removing Old Touches


    If you need to change old faucets with new ones as a part of your setup, after that the first thing you must do is disconnect the water. After doing so, turn on the faucets to drain pipes any water staying in the system. The procedure of removing the existing taps can be fairly troublesome as a result of the limited access that is usually the instance.
    Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly originate from the pipelines. Once the supply pipes have been removed, use the very same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming during this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing compound.
    Before carrying on to fit the new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.

    Suitable New Taps


    If the tails of the brand-new faucets are plastic, then you will require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end offers a connection to the current supply pipelines.
    If you need to fit a monobloc, after that you will certainly require reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
    Next off, place the tap in the placing opening in the bath/basin making certain that the washing machines are in location in between the tap and the sink. Protect the tap in position with the producer provided backnut. As soon as the tap is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet connectors. The previous type needs to be attached to the tap ends initially, tightening up just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.

    Installing the Tub


    Using both wooden boards under its feet, position the bath tub in the required placement. The wooden boards are helpful in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
    The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the bath tub till the spirit level reads degree.
    To install taps, fit all-time low of the furthest adaptable faucet adapter to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other tap.
    Turn on the supply of water and inspect all joints as well as new pipework for leakages and also tighten them if necessary. Fill up the bath tub as well as additionally examine the overflow electrical outlet as well as the regular electrical outlet for leakages.
    Ultimately, deal with the bath paneling as described in the supplier's user's manual. Tiling and also securing around the bathtub ought to wait until the bath tub has been made use of at least when as this will resolve it into its last placement.

    Getting ready for the Installation


    First of all, the sustaining frame provided with the bath must be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
    Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you make use of all of the provided washers.
    Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now be ready to be fitted in its final placement.

    Tiling Around the Tub


    In the location where the bath fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a stiff seal, causing the water to penetrate the wall surface between the bathroom and the tiling, resulting in problems with wetness as well as feasible leakages to the ceiling below.
    You can choose from a selection of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes as well as cartridges, and also are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of soaked newspaper or soft rope. Remember to always fill up the bathtub with water before sealing, to enable the activity experienced when the tub is in usage. The sealant can fracture fairly early if you do not think about this motion prior to securing.
    Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently readily available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub Yourself

    We are very drawn to How to Install a Bathtub Yourself and I really hope you enjoyed reading the new post. Sharing is nice. Helping people is fun. Kudos for your time. Visit us again soon.


    For best results, ring!

    Report this page